Lobro (302267) brand fits rear axles, all vans including Syncro.
These joints are particularly important if you have raised your van whether it's 2wd or 4wd. As the van rises, the stock CV joints will start to bind because the angle of the axle becomes too acute. The 944 CV kit has better articulation and won't fail as quickly as the stock joint.
This kit comes with the joint, boot, a sack of grease, hardware, and 12 point bolts. You may need the 12-point Socket 3/8th Drive Tool or Serrated CV/Axle Bolt Lock Washers.
If you wish to use the 944 joint kit on Syncro front inner, please see the Syncro Front Inner CV Joint Bolt & Lower Thermostat Housing Bolt. The bolts for the Syncro Front Inner are 2mm longer than the ones that come with this kit, so it is necessary to purchase the longer ones unless you are reusing your old bolts. You would need 6 bolts per cv joint kit.
If you wish to use the higher performance Redline grease, we carry the tub of Redline grease as well as the tube.
*Please note that the GKN/Lobro CV joints will not fit the Chinese axles on the market.*
Note: As stated in the Bentley factory service manual (page 42.8), your CV joints will need to be installed onto these axles with a press and a bit of anti-seize. New axles are machined to exacting tolerances and are a tight interference fit with the joint. Please be prepared for this step of the installation. Trying to pound them on will only lead to much frustration!
Ref ID: 94433190100
944 CV Joint Kits All Rear And Syncro Front Inner with Rockford Boot
CV Joint Fits All Rear And Syncro Front Inner
16" Syncro Rear Inner And Outer CV Joint Kit (302287)
Rockford CV Boot All Vans Rear + Syncro Front Inner
CV Boot - Rear All Models, Front Inner Syncro
-
Description
Lobro (302267) brand fits rear axles, all vans including Syncro.
These joints are particularly important if you have raised your van whether it's 2wd or 4wd. As the van rises, the stock CV joints will start to bind because the angle of the axle becomes too acute. The 944 CV kit has better articulation and won't fail as quickly as the stock joint.
This kit comes with the joint, boot, a sack of grease, hardware, and 12 point bolts. You may need the 12-point Socket 3/8th Drive Tool or Serrated CV/Axle Bolt Lock Washers.
If you wish to use the 944 joint kit on Syncro front inner, please see the Syncro Front Inner CV Joint Bolt & Lower Thermostat Housing Bolt. The bolts for the Syncro Front Inner are 2mm longer than the ones that come with this kit, so it is necessary to purchase the longer ones unless you are reusing your old bolts. You would need 6 bolts per cv joint kit.
If you wish to use the higher performance Redline grease, we carry the tub of Redline grease as well as the tube.
*Please note that the GKN/Lobro CV joints will not fit the Chinese axles on the market.*
Note: As stated in the Bentley factory service manual (page 42.8), your CV joints will need to be installed onto these axles with a press and a bit of anti-seize. New axles are machined to exacting tolerances and are a tight interference fit with the joint. Please be prepared for this step of the installation. Trying to pound them on will only lead to much frustration!
Ref ID: 94433190100
-
Finish Your Project
Complete your install with the products below
944 CV Joint Kits All Rear And Syncro Front Inner with Rockford Boot
ID: KT-000987 In stock.MSRP:$113.19Add to Cart The item has been addedCV Joint Fits All Rear And Syncro Front Inner
ID: 001885 In stock.MSRP:$65.95Add to Cart The item has been added16" Syncro Rear Inner And Outer CV Joint Kit (302287)
ID: 002741 In stock.MSRP:$129.95Add to Cart The item has been addedRockford CV Boot All Vans Rear + Syncro Front Inner
ID: KT-000979 In stock.MSRP:$23.24Add to Cart The item has been addedCV Boot - Rear All Models, Front Inner Syncro
ID: 001878 In stock.MSRP:$9.95Add to Cart The item has been added